1966 Coupe, 289-2bbl V8, C4 auto, Deluxe Pony interior.......................Clean title in hand
New parts installed:
Front fenders, Rear quarters, trunk floor, trunk drop downs,
Front frame rails, Rear frame rails, full length floor pans
Shelby fiberglass hood w/correct springs, Shelby front valance and stone guard, front bumper supports, parking lights, hood weather strip.
Grille, grille surround,
Grab-a-trak #620 springs, shocks, upper & lower control arms, Shelby drop installed, end links, front sway bar and poly bushings. Rear shocks
Wiring harness from firewall forward, Voltage regulator, wiper motor,
Battery tray
Woodgrain bezel and white face gauges, carpet, dash and dash surrounds,
All nuts, bolts and washers for front fenders, engine bay components, grille, valance, bumper and supports, all suspension parts, bezel, dash and surrounds
I'm sure I am forgetting others.
Parts not installed:
Full Pony interior upholstery
Full length console, glove box, door sills, kick panels, chrome heater controls
GT rear valance, rear bumper supports, gas tank w/new sending unit,
Quarter glass and vent window wetherstrips,
Driver door (rust free)
New assembly hardware packs for console, sills, glove box, rear bumper & supports, rear valance, kick panels, seat belts, etc
Many more small pieces that I am not listing.
Engine and tranny are in the car but not hooked up and running (original condition-not rebuilt). No exhaust installed. Was going to buy GT dual exhaust but didn't yet.
Car needs, exhaust, body alignment, upholstery installed, door panels, and rear bumper/valance installed....... plus paint.
I have been working on this for several years, I trusted a friend to weld in new quarters and inner wheel wells but he got them too hot and warped them. I don't have the resources to fix them. With school, job, family, house, etc. I just don't have the time, money or energy to complete the project.
Asking $6500. Located in Northern Kentucky close to Cincinnati.
New parts installed:
Front fenders, Rear quarters, trunk floor, trunk drop downs,
Front frame rails, Rear frame rails, full length floor pans
Shelby fiberglass hood w/correct springs, Shelby front valance and stone guard, front bumper supports, parking lights, hood weather strip.
Grille, grille surround,
Grab-a-trak #620 springs, shocks, upper & lower control arms, Shelby drop installed, end links, front sway bar and poly bushings. Rear shocks
Wiring harness from firewall forward, Voltage regulator, wiper motor,
Battery tray
Woodgrain bezel and white face gauges, carpet, dash and dash surrounds,
All nuts, bolts and washers for front fenders, engine bay components, grille, valance, bumper and supports, all suspension parts, bezel, dash and surrounds
I'm sure I am forgetting others.
Parts not installed:
Full Pony interior upholstery
Full length console, glove box, door sills, kick panels, chrome heater controls
GT rear valance, rear bumper supports, gas tank w/new sending unit,
Quarter glass and vent window wetherstrips,
Driver door (rust free)
New assembly hardware packs for console, sills, glove box, rear bumper & supports, rear valance, kick panels, seat belts, etc
Many more small pieces that I am not listing.
Engine and tranny are in the car but not hooked up and running (original condition-not rebuilt). No exhaust installed. Was going to buy GT dual exhaust but didn't yet.
Car needs, exhaust, body alignment, upholstery installed, door panels, and rear bumper/valance installed....... plus paint.
I have been working on this for several years, I trusted a friend to weld in new quarters and inner wheel wells but he got them too hot and warped them. I don't have the resources to fix them. With school, job, family, house, etc. I just don't have the time, money or energy to complete the project.
Asking $6500. Located in Northern Kentucky close to Cincinnati.