70 Fastback (302 Boss clone) Coyote swap. - Page 8 - Vintage Mustang Forums

 52Likes
Reply
 
Thread Tools
post #106 of 117 (permalink) Old 03-08-2017, 11:43 PM
Junior Member
 
Join Date: Jul 2013
Posts: 1
What radiator are you using? I just bought a 2012 mustang that i may use for a parts in my 65 mustang... Thanks
eloyn7 is offline  
Sponsored Links
Advertisement
 
post #107 of 117 (permalink) Old 03-09-2017, 10:25 AM Thread Starter
Senior Member
 
Dalpilot's Avatar
 
Join Date: Jan 2016
Posts: 101
I found it on ebay. I just looked for one with 1 1/2 inlet and outlet ports on the correct sides. Its a 3 row aluminum. Nicely built.

1970 302 Boss, (Clone)
2016 Coyote with a T56 and a few other mods. "Keeping it stock."
Dalpilot is offline  
post #108 of 117 (permalink) Old 03-10-2017, 10:04 PM Thread Starter
Senior Member
 
Dalpilot's Avatar
 
Join Date: Jan 2016
Posts: 101
Last piece of the puzzle showed up today.







Exhaust went in so danged easy. Less than 45 minutes, by myself, with cutting 2 of the pipes to length. Still need to adjust and tighten it up. Going to clamp it till I can get it to a shop to put either a flange or vbands on it. I would definitely recommend this exhaust to anyone, incredible look and fit.





Gas goes in tomorrow and then I begin testing everything out. Might start it tomorrow.
Huntingky, rusty1161 and 68Hildago like this.

1970 302 Boss, (Clone)
2016 Coyote with a T56 and a few other mods. "Keeping it stock."
Dalpilot is offline  
 
post #109 of 117 (permalink) Old 03-12-2017, 12:34 AM Thread Starter
Senior Member
 
Dalpilot's Avatar
 
Join Date: Jan 2016
Posts: 101
No leaks, exhaust is in, so what the hack.

https://youtu.be/4WBsGbL9-kw
Turnall and outnumbered421 like this.

1970 302 Boss, (Clone)
2016 Coyote with a T56 and a few other mods. "Keeping it stock."
Dalpilot is offline  
post #110 of 117 (permalink) Old 03-12-2017, 09:33 AM
Senior Member
 
Join Date: Dec 2014
Posts: 597
Congrats! There's nothing like starting it for the first time.
Chaplin is online now  
post #111 of 117 (permalink) Old 03-12-2017, 02:54 PM
Member
 
Join Date: Aug 2013
Posts: 45
The vacuum canisters and all the hoses go to the CMCV. They can be removed and locked out.

CMCV LOCK OUT 2015 - 2017 Mustang GT & Shelby GT350 [477191] - $39.99 : Modular Motorsports, Home of the Worlds Fastest Modular Engines
blutruck1 is offline  
post #112 of 117 (permalink) Old 03-14-2017, 07:46 PM Thread Starter
Senior Member
 
Dalpilot's Avatar
 
Join Date: Jan 2016
Posts: 101
Thanks, I figured it out a little after that pic was taken, talked to my tuner about it and came up with a solution.

1970 302 Boss, (Clone)
2016 Coyote with a T56 and a few other mods. "Keeping it stock."
Dalpilot is offline  
post #113 of 117 (permalink) Old 03-20-2017, 11:29 PM Thread Starter
Senior Member
 
Dalpilot's Avatar
 
Join Date: Jan 2016
Posts: 101
It wouldn't rev above idle so I sent the pcm back to FPP. Turns out the pcm was fried, not sure why but Ford sent out a new one no questions asked. Hopefully it will get here tomorrow.

1970 302 Boss, (Clone)
2016 Coyote with a T56 and a few other mods. "Keeping it stock."
Dalpilot is offline  
post #114 of 117 (permalink) Old 03-23-2017, 03:23 PM Thread Starter
Senior Member
 
Dalpilot's Avatar
 
Join Date: Jan 2016
Posts: 101
New PCM came in but it still wouldn't rev above idle. Checked several things and the pedal was good, TPS was good but it was like it had no signal. Tracked down two wires, (both blue), to the pedal that were acting opposite of the way they should. A few calls to Ford Racing tech and they sent out a diagram. Sure enough pin 5 and 6 were backwards wired. Swapped the wires out, viola!

https://youtu.be/EOezQ_UV6Gk

It sure felt good even without any glass in the car, dash or interior. This thing is a beast and I barely got on it.

1970 302 Boss, (Clone)
2016 Coyote with a T56 and a few other mods. "Keeping it stock."
Dalpilot is offline  
post #115 of 117 (permalink) Old 03-24-2017, 11:22 PM Thread Starter
Senior Member
 
Dalpilot's Avatar
 
Join Date: Jan 2016
Posts: 101
Finished welding up the trans tunnel and the hushmat, (everywhere but under the drivers seat but its coming out to out carpet in). Then put the bulbs in the brake lights and suddenly realized I am finished with things I can do until it gets back from paint. Sooooo, next weekend it goes to my painter. Woo hoo.

I also ordered fold down rear seats and some new exterior stuff last night. Its amazing how fast it came together. At the end of last July I pulled the engine and trans to get started.

Let her outside to work on her tan after driving it around the neighborhood a few miles. The T-56 was a great move. Smooth as silk.





SWPruett and rusty1161 like this.

1970 302 Boss, (Clone)
2016 Coyote with a T56 and a few other mods. "Keeping it stock."
Dalpilot is offline  
post #116 of 117 (permalink) Old 03-25-2017, 06:16 AM
Senior Member
 
latoracing's Avatar
 
Join Date: Apr 2012
Location: NC
Posts: 731
Now that you have it going to paint, you're gonna be looking for something else to weld on lol. You did quite well with getting all that work done in a "short" time frame. Great job. Congrats!

I have never "made" anything, I just modify the things around me into useful items with abilities that were GIVEN to me.

Mike
latoracing is offline  
post #117 of 117 (permalink) Old 03-25-2017, 07:40 AM Thread Starter
Senior Member
 
Dalpilot's Avatar
 
Join Date: Jan 2016
Posts: 101
Thanks Mike and thanks for answering all my questions. It helped immensely.

1970 302 Boss, (Clone)
2016 Coyote with a T56 and a few other mods. "Keeping it stock."
Dalpilot is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Vintage Mustang Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are Off

 
For the best viewing experience please update your browser to Google Chrome