Vintage Mustang Forums - View Profile: Harleydave

Harleydave Harleydave is offline

Senior Member

  Visitor Messages

Showing Visitor Messages 1 to 3 of 3
  1. Harleydave
    01-27-2015 12:02 PM - permalink
    Harleydave
    Howdy, and thank you. I really don't have a build thread, but I have been fairly active here. If you search the threads I started you will see most of it. I bought a rolling rusty chassis three years ago. Dave
  2. Sacramento Stang
    01-25-2015 01:32 PM - permalink
    Sacramento Stang
    Dave very nice 68. I to have the same color body style in 67. Had to drop you a line and say nice job. Do you have a build thread?
  3. Fastback Steve
    10-05-2014 03:37 AM - permalink
    Fastback Steve
    Dave, Concerning you rear seal problem I actually changed mine with the engine in the car about 20 years ago. I disconnected the idler arm and steering linkage and pulled it down. This allowed me the remove the stock pan without lifting the engine. I had to rotate the crank by hand to clear the journals with the pan. I then loosened the main caps. I was able to use a small drift pin and push on one side of the seal. The seal slid around the crank enough to where I could get a hold of it with plies and pull it out. I oiled up the new one and slowly walked it in by hand. I put some permatex on the ends of the bottom seal and put it back together. It worked great for me. Good luck.
    Steve

  About Me

  • About Harleydave
    Biography
    68 Fastback
    Location
    Livingston, New York
    Interests
    http://forums.vintage-mustang.com/build-forum/916033-68-fastback-build-thread.html
    Occupation
    Engineer
  • Signature

    68 Fastback.
    351Windsor, 4sp, 8" 3.40 TracLok
    http://forums.vintage-mustang.com/bu...ld-thread.html

  Statistics

Total Posts
Albums
Visitor Messages
General Information
  • Last Activity: Today 02:00 PM
  • Join Date: 05-17-2012
  • Referrals: 0

  Friends

Showing Friends 1 to 1 of 1
  • jimsauto
    • jimsauto is offline

  Mentions

No results to display...

  Quotes

11-21-2016
02:46 PM - Harleydave quoted Huskinhano in post Rack & Pinion
Dave, the Unisteer mimics the d...
11-19-2016
12:29 AM - Ponyboy quoted Harleydave in post Help me pick my new steering wheel
http://i1174.photobucket.com/al...
11-11-2016
11:53 AM - Harleydave quoted Huskinhano in post Rack & Pinion
Dave, I never really concerned ...
11-08-2016
05:51 PM - donkeykong quoted Harleydave in post Rack & Pinion
Watched the TCP install video. ...
10:24 AM - PetesPonies quoted Harleydave in post Rack & Pinion
I have manual steering now. I h...
08:26 AM - stephen_wilson quoted Harleydave in post Rack & Pinion
The main thing was the use of e...
08:15 AM - Harleydave quoted stephen_wilson in post Rack & Pinion
I'm curious, what didn't you like a...
08:06 AM - stephen_wilson quoted Harleydave in post Rack & Pinion
Watched the TCP install video. ...
07:06 AM - Harleydave quoted PetesPonies in post Rack & Pinion
So why not upgrade the original ...
11-07-2016
06:39 PM - donkeykong quoted Harleydave in post Rack & Pinion
I am looking at upgrading to th...
03:28 PM - Harleydave quoted NotAGuest in post Help with picking parts for 1968 Fastback
Also to clear some things up. ...
10-25-2016
02:35 PM - 68FordMustang quoted Harleydave in post Engine swap 68....by by 289
I used a stock 351W. 8" rear wi...
10-18-2016
04:40 PM - RyanSterling966 quoted Harleydave in post Original 8" Conversion to Traction Lock..How to?
I went this route. Mustand 8...
10-14-2016
08:36 AM - Harleydave quoted mqu02 in post 4 Speed Toploader Input Shaft Install?!
From my experience (been i...
09-26-2016
11:27 PM - PetesPonies quoted Harleydave in post Exhaust Tips that fill the cutouts?
http://i1174.photobucket.com/al...
09-18-2016
12:23 PM - 2nd 66 quoted Harleydave in post Will LUCAS oil additive work
I use VR-1 10/30 without additi...
09-11-2016
08:46 AM - Harleydave quoted Paul1958 in post Wiring question
Dave, I would make the jumpe...
09-10-2016
11:41 PM - Paul1958 quoted Harleydave in post Wiring question
I am trying to eliminate the pi...
08-31-2016
03:43 PM - Orndorff8908 quoted Harleydave in post A month long problem. Hopefully I'll find help here.
What is the timing set at? ...
08-30-2016
05:43 PM - ddaytona1 quoted Harleydave in post 67 fastback fold down seat latch cover need photo
Correct. And the holes in the f...

  Feedback

iTrader Profile Recent Ratings
Feedback Score:
Positive Feedback:
0
0%
Members who left positive:
Members who left negative:
0
0
Total positive feedback: 0
Submit Feedback
  Past
Month
Past
6 Months
Past
12 Months
Positive Positive 0 0 0
Neutral Neutral 0 0 0
Negative Negative 0 0 0
 
For the best viewing experience please update your browser to Google Chrome