Picture of correctly wired '66 starter solenoid? - Vintage Mustang Forums
Vintage Mustang Forum
HomeForumGalleryClassifiedsAbout UsAdvertiseContact Us
» Auto Insurance
» Featured Product
Go Back   Vintage Mustang Forums > General Discussion > Vintage Mustang Forum
Vintage-Mustang.com is the premier Ford Mustang Forum on the internet. Registered Users do not see the above ads.
Reply
 
Thread Tools
Old 01-18-2003, 05:33 PM   #1 (permalink)
Senior Member
 
Join Date: Sep 2001
Location: Alpharetta, GA
Posts: 259
Default

Does anyone have a picture of a correctly wired starter solenoid for a '66 inline six? I believe the wiring on the solenoid is the same for 8cyl also, so a picture of that would work.

I'm especially interested in a wire that has a round end that is only big enough to fit onto the two smaller posts rather than on the bigger posts that the battery cable attaches to; does it get bolted to the smaller post on the solenoid? If so, which post. I previously had it rigged with some wire and tied to the the post where the battery connects to.

My solenoid has been acting up and finally it won't start. The car is sitting in my work parking lot. So, I figured I'd try to get the wiring all correct this time around.

Thanks in advance for any pictures.
Dan
__________________
Sold the Mustang but not the Mustang hobby... I will get a Boss 302!
'66 Mustang Convertible, I6, Candy Apple Red (link to my restoration website)
http://www.dykstra.cc/dykstra/1966Mu...es/carbird.jpg
danieldykstra is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 01-18-2003, 06:19 PM   #2 (permalink)
Senior Member
 
Join Date: Sep 2000
Location: Atlanta
Posts: 4,800
Default

Call me, 770-740-8703, I'll eyeball it for you over the phone-I'm pretty sure they are all the same.

J. Boggs
theboogins is offline   Reply With Quote Quick reply to this message
Old 01-18-2003, 06:48 PM   #3 (permalink)
Senior Member
 
Join Date: Sep 2001
Location: Alpharetta, GA
Posts: 259
Default

Anybody willing to snap a quick closeup digital pic?

If so, please email it to me at dan@dykstra.cc

Thanks.
Dan
__________________
Sold the Mustang but not the Mustang hobby... I will get a Boss 302!
'66 Mustang Convertible, I6, Candy Apple Red (link to my restoration website)
http://www.dykstra.cc/dykstra/1966Mu...es/carbird.jpg
danieldykstra is offline   Reply With Quote Quick reply to this message
Old 01-18-2003, 07:02 PM   #4 (permalink)
Guest
 
Posts: n/a
Default

this should answer your questions... http://www.early-mustang.com/charles/DSC00030.JPG
  Reply With Quote Quick reply to this message
Old 01-18-2003, 07:31 PM   #5 (permalink)
Senior Member
 
Join Date: Sep 2001
Location: Alpharetta, GA
Posts: 259
Default

Charles, thanks for the picture.

I have another wire that isn't shown in your picture. It has a hard rubber molded end with a small metal eyelet. I had it tied to the battery side of the solenoid. But the eyelet is too small to fit onto the positive side of the solenoid. Do you have any idea what this may be?

Thanks.
__________________
Sold the Mustang but not the Mustang hobby... I will get a Boss 302!
'66 Mustang Convertible, I6, Candy Apple Red (link to my restoration website)
http://www.dykstra.cc/dykstra/1966Mu...es/carbird.jpg
danieldykstra is offline   Reply With Quote Quick reply to this message
Old 01-18-2003, 08:22 PM   #6 (permalink)
Guest
 
Posts: n/a
Default

it's for the power top. it should mount to the positive side of the solenoid.
  Reply With Quote Quick reply to this message
Old 01-19-2003, 10:02 AM   #7 (permalink)
Senior Member
 
widgit's Avatar
 
Join Date: Nov 2002
Location: Des Moines, IA
Posts: 1,183
Default

The fabric coated wire is missing the fabric on my car. Is it available?...or do I need a complete harness?
__________________

"Your actions speak louder than words"

Misc Pics
widgit is offline   Reply With Quote Quick reply to this message
Old 01-19-2003, 02:50 PM   #8 (permalink)
Guest
 
Posts: n/a
Default

the best solution i have found is to buy an original pink resistor wire for behind the dash. this has a long piece of the tar coated stuff you can use to transfer. otherwise, yes, you can replace the harness and it will have a new piece on it.
  Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Vintage Mustang Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are Off


Powered by vBadvanced CMPS v3.2.2

All times are GMT -4. The time now is 04:29 PM.


Powered by vBulletin® Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
SEO by vBSEO 3.3.2 ©2009, Crawlability, Inc.