Vintage Mustang Forums - View Profile: gikort

gikort gikort is online now

Senior Member

  Visitor Messages

Showing Visitor Messages 1 to 6 of 6
  1. jkordzi
    09-28-2014 06:23 PM - permalink
    jkordzi
    I pretty much have this done but wanted to know if you had any problem clocking the pitman arm correctly? I see that the Trooper is indexed every 90 degrees but none of those positions seem right. Thanks.
  2. 67Riley
    05-04-2014 07:33 AM - permalink
    67Riley
    Gikort, saw your note about installing a '95 T5 in your '67 coupe. I have a '67 coupe and about to install a '95 T5 in it. Ordered the modern driveline hydraulic clutch set up with external slave. I will be using the '95 bellhousing. I've been told the starter (tranny is currently a T10 four speed) won't fit and I will need a different one. Any tips you can provide would be appreciated. JC
  3. crane550
    04-18-2014 10:09 PM - permalink
    crane550
    Hi,

    Didn't end up going SLC route on the way to Vegas, but we are going that way on Sunday (we think.)

    Are you in Vegas? Text me at 208-407-4947, I would love to see your car. I was looking for it at the show but didn't see it.

    Alex
  4. jkordzi
    02-26-2014 10:05 PM - permalink
    jkordzi
    What PS pump did you use? Would you describe in more detail where you got the bearing for the end of the steering column and how you installed it? Did you have to cut part of the steering column tube off? Thanks again.
  5. jkordzi
    02-25-2014 06:25 PM - permalink
    jkordzi
    Thanks for the write-up on the DIY Trooper PS install. I'm thinking of doing it to my 65. How has the PS system been running for you - would you do it again? Any problems with the pitman arm? Instead of welding the pitman arm, did you look into getting the output shaft from the Trooper box machined to fit the Mustang arm? Thanks.
  6. brent's68mustang
    03-26-2013 06:16 PM - permalink
    brent's68mustang
    nice mustang. I was thinking about putting torq thrust d's on my mustang 15X7. What size tires are you running and do you have any rubbing issues. Brent

  About Me

  Statistics

Total Posts
Albums
Visitor Messages
General Information
  • Last Activity: Today 07:01 PM
  • Join Date: 11-26-2010
  • Referrals: 0

  Friends

Showing Friends 1 to 2 of 2

  Mentions

04-14-2019
12:05 AM - Turnall mentioned gikort in post 66 T Code - T is for Transformation
... close attention to gikorts build. Makes me tha...
03-31-2019
08:20 PM - Turnall mentioned gikort in post Need Engine Gurus
By the way gikort, was the block align...
10-19-2018
02:58 PM - gikort mentioned mikeyhunts in post 1967 T/A Group II Clone
...ably 7 years now. mikeyhunts Your guess is as goo...
09-26-2018
06:21 PM - gikort mentioned app01 in post 3" Wheel Studs
... expensive ARP ones app01 posted because of wh...
04-02-2018
08:13 PM - Turnall mentioned gikort in post 66 T Code - T is for Transformation
... check your thread gikort. To start off, I've ...
01-13-2018
06:12 PM - gikort mentioned Silver in post 1967 T/A Group II Clone
...nternally balanced. SilverbluePB had his engine...

  Quotes

04-15-2019
08:20 PM - Turnall quoted gikort in post Need Engine Gurus
Hey Allen, built to spin to...
04:06 PM - gikort quoted GT350HR in post Need Engine Gurus
gikort, You may have ...
04:04 PM - gikort quoted Huskinhano in post Need Engine Gurus
What about the thrust surface? ...
04:03 PM - gikort quoted daves67ss in post Need Engine Gurus
That looks like they machined ...
04:02 PM - gikort quoted Turnall in post Need Engine Gurus
I would agree. What rpm do ...
04-07-2019
03:51 PM - gikort quoted Scarlet-302 in post Need Engine Gurus
From experience, its not too bad...
04-06-2019
10:34 PM - gikort quoted bdub4u in post 1967 T/A Group II Clone
What did that cost ya? Tryi...
10:26 PM - gikort quoted Woodchuck in post Need Engine Gurus
Gold/Brass colored is NOT good...
04:26 PM - bdub4u quoted gikort in post 1967 T/A Group II Clone
Got the heads back. 16 new...
04-05-2019
10:29 PM - Turnall quoted gikort in post 66 T Code - T is for Transformation
Ah yes, i think i remember ...
10:12 PM - gikort quoted Scarlet-302 in post Need Engine Gurus
So when cold it feels easy to ro...
10:03 PM - gikort quoted Turnall in post 66 T Code - T is for Transformation
World Products Windsor Sr. T...
08:32 PM - Turnall quoted gikort in post 66 T Code - T is for Transformation
Looking good there allen! W...
04-04-2019
04:08 PM - gikort quoted Turnall in post Need Engine Gurus
Any word from the shop? Let ...
04:05 PM - gikort quoted GypsyR in post Need Engine Gurus
The situation Scarlet descr...
03:46 PM - gikort quoted Scarlet-302 in post Need Engine Gurus
Did you ever mention what piston...
03:30 PM - gikort quoted Scarlet-302 in post Need Engine Gurus
Have you tried starting it again...
04-03-2019
08:15 AM - Turnall quoted gikort in post Need Engine Gurus
I turned it over by hand la...
04-01-2019
02:47 PM - gikort quoted Scarlet-302 in post Need Engine Gurus
Have you tried starting it again...
02:42 PM - gikort quoted Turnall in post Need Engine Gurus
Maybe the springs on the val...

  Feedback

iTrader Profile Recent Ratings
Feedback Score:
Positive Feedback:
0
0%
Members who left positive:
Members who left negative:
0
0
Total positive feedback: 0
Submit Feedback
  Past
Month
Past
6 Months
Past
12 Months
Positive Positive 0 0 0
Neutral Neutral 0 0 0
Negative Negative 0 0 0
 
For the best viewing experience please update your browser to Google Chrome